Rki-instruments GX-2012 Manual Manual de usuario Pagina 64
- Pagina / 185
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
56 • Data Logging GX-2012 Operator’s Manual
Data Logging
NOTE: The GX-2012 logs data in both Normal Mode and Bar Hole Mode.
The GX-2012 features the ability to log data to its internal memory and
download it to a computer via the infrared communications port located just
below the RESET SILENCE button. It logs gas readings during normal
operation, alarm data, and calibration data.
NOTE: The data logging function is separate from the snap logging
function. For a description of the snap logging function, see “Snap
Log Mode” on page 33.
To utilize the GX-2012’s downloading capability, you will need the GX-2012
downloading software and a computer with an infrared port or a USB port
that runs one of the following operating systems: Windows XP, Windows
Vista, or Windows 7. If your computer has an infrared port, then no
additional accessories are needed to download data from the GX-2012. If
your computer does not have an infrared port but does have a USB port, a
USB/IrDA adapter cable can be used to download data from the GX-2012
using a USB port. The downloading software is available from RKI
Instruments, Inc. The adapter cable is also available from RKI or may be
purchased at a computer or electronics supply store.
For a complete description of the downloading software and procedures for
downloading data to a computer, see the GX-2012 Data Logger Management
Program Operator’s Manual.
SDM-2012
The GX-2012 can be used with the SDM-2012 if desired. The
SDM-2012 can charge the instrument if the lithium ion battery pack is being
used. It can also bump test, calibrate, and retrieve saved data. The SDM-2012
can be operated as a single, stand-alone unit or can be used with up to 9 other
SDM-2012s and operated using a computer. For more information about the
operation of the SDM-2012, see the SDM-2012 operator’s manual.
- Operator’s Manual 1
- GX-2012 Operator’s Manual 2
- Warranty 3
- Table of Contents 4
- Chapter 1: Introduction 9
- About the GX-2012 9
- Specifications 11
- About this Manual 12
- Chapter 2: Description 13
- Instrument Description 13
- Combustible Gas Sensors 15
- Oxygen Sensor 15
- CO and H 15
- S Sensors 15
- Hollow Side 16
- Dummy Sensor 16
- Top Flat 16
- Button Function(s) 17
- Vibrator 18
- Batteries 18
- Flow Chamber 19
- Sensors and Filters 19
- Inlet Filter Holder 19
- Sample Hose 20
- Optional Accessories 21
- End Plugged 24
- Purge Tee Fitting 26
- External Dilution Fitting 26
- Start Up, Normal Mode 27
- With All Modes Active 33
- AIr 35
- HOLD AIR 35
- Measuring Mode, Normal 36
- Operation 36
- Using the Purge Tee Fitting 37
- Using the Dilution Fitting 38
- Combustible Gas Detection 39
- Snap Log Mode 41
- Measuring Mode, Alarms 44
- Responding to Alarms 47
- Responding to Battery Alarms 48
- 000 MPU failure 49
- 010 RAM failure 49
- 021 EEPROM failure 49
- 031 FLASH memory failure 49
- Inert Mode 50
- Display Mode 51
- HC 52
- SEL 52
- HC RANGE 52
- STEL Screen 53
- TWA Screen 53
- Alarm Points Screen 54
- Operation Time Screen 55
- Date/Time Screen 56
- Remaining Log Time Screen 56
- Clear Data Logger Screens 57
- Pump OFF Screen 58
- User ID Screen 59
- Station ID Screen 60
- Snap Logging Screen 61
- CO 62
- H2S 62
- Peak Bar Select Screen 63
- SDM-2012 64
- Data Logging 64
- Calibration Mode 65
- Bump Testing the GX-2012 74
- Start Up, Bar Hole Mode 81
- 0 87
- 20.9 87
- Bar Hole Testing 88
- Start Up, Leak Check Mode 92
- Leak Testing 99
- Overscale Conditions 100
- LEAK CK MODE 101
- Peak Hold Mode 102
- 103
- Chapter 6: Maintenance Mode 108
- Overview 108
- Using Maintenance Mode 109
- O2 115
- CO 115
- H2S 115
- Performing a Bump Test 119
- Turning Portuguese On or Off 146
- Channel Display Setting 147
- Exiting Maintenance Mode 150
- Troubleshooting 151
- Symptoms 152
- Probable 152
- Recommended Action 152
- OPEN CLOSE 154
- Slide Latch This Way 155
- Charge LED 156
- Power Supply Jack 156
- AC Power Supply 156
- DC Powered Charging Station 157
- Red Charging LED 158
- AC Powered Charging Station 159
- Battery Pack 161
- LEL Filter 162
- CO Filter 162
- Figure 27: Replacing a Sensor 163
- Part Number Description 166
- Sample Bag 169
- Preparing for Calibration or 170
- Bump Testing 170
- Calibrating the GX-2012 172
- Parts List 185
Relacionado con productos y manuales para Sensores Rki-instruments GX-2012 Manual
Sensores Rki-instruments GX-86A Manual de usuario
(39 paginas)
(39 paginas)
Sensores Rki-instruments GX-94 Manual de usuario
(52 paginas)
(52 paginas)
Sensores Rki-instruments RX-517 Manual de usuario
(36 paginas)
(36 paginas)
Sensores Rki-instruments SDM-2009 Manual de usuario
(56 paginas)
(56 paginas)
Sensores Rki-instruments SM-2003U Manual de usuario
(46 paginas)
(46 paginas)
Sensores Rki-instruments SM-2009U Manual de usuario
(55 paginas)
(55 paginas)
Sensores Rki-instruments SDM-E2 Manual de usuario
(224 paginas)
(224 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.128 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales