Rki-instruments EAGLE 2 Manual Manual de usuario Pagina 281
- Pagina / 309
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
EAGLE 2 Operator’s Manual Start Up, Bar Hole Mode • 271
NORMAL MODE and LEAK CHECK MODE will be the
only choices displayed. In this case, see “Turning On the
EAGLE 2” on page 22 or “Turning On the EAGLE 2, Leak
Check Mode” on page 279.
1. Connect the sample hose to the EAGLE 2’s quick connect inlet
fitting.
2. Connect the bar hole probe to the sample hose’s quick connect
fitting.
3. Press and briefly hold down the POWER ENTER RESET button.
Release the button when you hear a beep.
4. The LCD will show the following screen for about ten seconds.
5. The Battery Voltage Screen appears for a few seconds.
6. The Mode Select Screen displays.
7. The cursor will flash in front of NORMAL MODE. Use the
RANGE ▼ SHIFT button to move the cursor next to BAR HOLE
MODE.
8. With Bar Hole Mode selected, press and release the POWER
ENTER RESET button to begin the Bar Hole Mode startup
sequence.
GAS MONITOR
EAGLE 2
BATTERY MIN:
4.3 VOLTS
BATTERY NOW:
5.2 VOLTS
> NORMAL MODE
BAR HOLE MODE
LEAK CHECK MODE
- Operator’s Manual 1
- EAGLE 2 Operator’s Manual 2
- Table of Contents 3
- Overview 11
- About the EAGLE 2 11
- Chapter 1: Introduction 11
- Specifications 13
- About this Manual 14
- Chapter 2: Description 16
- Instrument Description 16
- Oxygen Sensor 19
- CO and H 19
- S Sensors 19
- Control Buttons 20
- Main PCB 21
- Display PCB 21
- I.S. Barrier PCB (not visble) 21
- Alarm LEDs 22
- Infrared Communications Port 22
- Battery Case & Batteries 23
- Flow System 24
- Standard Accessories 25
- Sample Hose 26
- Rechargeable Ni-MH Batteries 27
- Battery Chargers 27
- Optional Probes 28
- Figure 12: Barhole Probe 29
- 1:1 Dilution Fitting 31
- 3:1 Dilution Fitting 31
- Chapter 3: Operation 32
- OXY 20.9vol% 37
- Continuous Operation 38
- Measuring Mode, Normal 39
- Operation 39
- Using Exhaust Tubing 41
- Combustible Gas Detection 41
- Measuring Mode, Alarms 45
- Alarm Indications 46
- Low Flow 47
- Low Battery Warning 47
- Dead Battery Alarm 47
- Sensor Failure 47
- Responding to Alarms 48
- Responding to Battery Alarms 49
- Display Mode 50
- Peak Screen 51
- Battery Voltage Screen 52
- Gas Display Screen 52
- STEL Screen 56
- TWA Screen 56
- View Alarm Settings Screen 56
- Select User ID Screen 58
- Select Station ID Screen 60
- OPERATION 61
- Date/Time Screen 62
- Data Logging Screen 62
- Data Logging 63
- Interval 64
- Data Logging Time 64
- Chapter 4: Calibration Mode 65
- Calibration Supplies and 66
- Equipment 66
- Calibrating Using the Auto 68
- Chapter 5: Maintenance 80
- Troubleshooting 80
- B OXY 20.9vol% 82
- T 82
- ON OFF CHARGING 85
- ON ON READY/FULL 85
- BLINKING OFF FAIL 85
- OFF ON CONTINUOUS 85
- Charcoal Filter 89
- Checking the Combustible Gas 90
- Sensor’s Condition 90
- Replacing a Sensor 90
- Figure 22: Replacing a Sensor 91
- General Parts List 94
- Calibration Cylinder 96
- Regulator 96
- Hose Clamp 96
- Calibration Tubing 96
- Entering Calibration Mode 97
- Calibrating Using the Single 104
- Calibration Method 104
- SELECT SENSOR 109
- TO CALIBRATE 109
- >ESCAPE 109
- CH4 OXY 109
- H2S CO 109
- Parts List 110
- Appendix B: Setup Mode 111
- Tips for Using Setup Mode 112
- GAS MONITOR 113
- EAGLE 2 S 113
- Setting the Date and Time 114
- Setting the Date Format 114
- Setting the Battery Type 115
- Configuring the Channels 115
- CAT(0-50000ppm CH4) 122
- SETTING EV 122
- UP/DOWN THEN ENTER 122
- USER AND 128
- STATION ID’S 128
- FRESH AIR ADJUST 130
- ON POWERUP 130
- CALIBRATION 133
- REMINDER 133
- Updating LC/BH Mode Setting 134
- CONFIRMATION ALERT 136
- RESTORE DEFAULT 138
- CONFIGURATION? 138
- Updating the Language Setting 140
- SAVE ALL CHANGES 141
- IN MEMORY? 141
- ARE YOU SURE YOU 141
- WANT TO SAVE ALL 141
- CHANGES IN MEMORY? 141
- SUB2 SUB1SUB3 142
- Sub PCB Positions 142
- CONFIGURE CHANNELS 143
- > CH1: CAT (CH4) 143
- CH2: OXY (OXY) 143
- CH3: H2S (H2S) 143
- CH4: OP1 (PID) 143
- Sub PCBs and CONFIGURE GASES 144
- ESM & IR SENSOR 145
- ARE AUTOMATICALLY 145
- DETECTED 145
- MANUAL SELECTION 145
- IS NOT POSSIBLE 145
- Appendix D: PID Sensors 146
- Description 146
- PID Sub PCB 147
- PID Probe 147
- Start Up and Normal Operation 148
- IBL 0.00ppm 149
- 149
- RELATIVE RESPONSE 150
- TO CALIBRATED GAS 150
- FOR PID SENSOR 150
- PID Calibration 153
- Maintenance 170
- Lamp Window 172
- Figure 31: Using Removal Tool 176
- Replacing the Electrode Stack 178
- Figure 33: Using Removal Tool 179
- Replacing the PID Sensor 181
- EAGLE 2 S 182
- 2000 ppm IBL 185
- ESM-01 Sensor 190
- ESM-01 Calibration 191
- CALIBRATION MODE 192
- > AUTO CALIBRATION 192
- SINGLE CALIBRATION 192
- PERFORM AIR ADJUST 192
- NORMAL OPERATION 192
- Replacing the H 210
- S Scrubber in the SO 210
- and HCN Sensors 210
- Part Number Description 213
- Appendix F: TC Sensors 214
- TC Sensor 215
- TC Sub PCB 215
- Catalytic (LEL) Sensor Screen 216
- * * * WARNING * * * 217
- NO LEL ALARMS IF 217
- CAT (LEL) IS DISABLED 217
- CAT (LEL) SENSOR 217
- Infrared CO 234
- Infrared Sub PCB 234
- End Caps 235
- 0-5 %vol 0.04 %vol 236
- 0-10,000 ppm 400 ppm 236
- 0-60 %vol 0.0 %vol 236
- Calibration 237
- 228 • Infrared CO 238
- Calibration • 229 239
- 230 • Infrared CO 240
- Calibration • 231 241
- 232 • Infrared CO 242
- Calibration • 233 243
- Table 24: IR CO 244
- Sensor Calibration Times 244
- Calibration • 235 245
- Infrared Hydrocarbon Sensor 263
- METHANE ELIMINATION 276
- DISABLED 276
- Calibration 279
- Start Up, Bar Hole Mode 280
- BAR HOLE MODE 285
- CH4 0 %LEL 285
- OXY 20.9 vol% 285
- ENTER: MEASURE 285
- ADJUST: PURGE 285
- Bar Hole Testing 286
- Start Up, Leak Check Mode 289
- LEAK CHECK MODE 294
- CH4 0 ppm 294
- Locating a Leak 295
- Appendix M: Tank Tester Model 297
- CONNECT FLOAT PROBE 299
- Start Up 306
- MODE SELECT 308
- NORMAL MODE 308
- Warranty 309
Relacionado con productos y manuales para Sensores Rki-instruments EAGLE 2 Manual
Sensores Rki-instruments Gas Tracer Manual de usuario
(234 paginas)
(234 paginas)
(2 paginas)
(66 paginas)
Sensores Rki-instruments GX-82 Manual de usuario
(22 paginas)
(22 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales